HygroMatik HeaterLine HL 12 Скачать руководство пользователя страница 58

Страница: 58 / 70

Page 58

Open water supply.

Switch on unit and check for leakage after 15-30 min-
utes of operation.

If leakage occurs, switch off power supply and repair the leaks,
following safety instructions for work on live components!

9.13

Checking Cable Screw Connections,

Heater Element Wires

Check that all cable screw connections are securely
tightened

Ensure that heating element cable is not dammaged.

Warning:

Loose cable connections cause excessive contact

resistance and overheating of contact surfaces.

9.14

Operational Check

Start up the unit and operate for a few minutes, ideally
at maximum output..

Check safety devices.

Check hose connections for possible leaks.

9.15

Dismantling

Once the steam humidifier will no longer be used, dismantle
(demolish or scrap) it by following the installation procedures in
reverse order.

Warning:

Dismantling of the unit may only be performed by

qualified personnel. Electrical dismantling may only be per-
formed by trained electricians.

Obey the safety guidelines in section “Safety Instructions,” espe-
cially the guidelines for disposal.

Содержание HeaterLine HL 12







































































Результаты поиска

Содержание HeaterLine HL 12

Отзывы:

Похожие инструкции для HeaterLine HL 12

Бренды по названию

Популярные бренды

HygroMatik HeaterLine HL 12, Руководство пользователя

Результаты поиска

Содержание HeaterLine HL 12

Отзывы:

Похожие инструкции для HeaterLine HL 12

Бренды по названию

Популярные бренды