manualshive.com logo in svg

HygroMatik HeaterLine HL 12, Руководство пользователя

Поделиться
Скачать
HygroMatik HeaterLine HL 12 Скачать руководство пользователя страница 52

                                                                                                             

                                                                                                                                              Page 52

9.6

Cleaning connection hoses, cylinder base

and nozzle

When operating with partially softened water or tap water scale
can be discharged with the steam flow and can settle in the noz-
zle (3) that is in the steam hose adapter. Therefore, this nozzle
should be tested regularly as part of the general maintenance
review and cleaned if necessary.

Installation

»

Install new heater element, replacing the parts in the 
correct sequence according to the diagram, and screw 
nut with a torque of 5Nm onto the pressure plate.

»

Insert the heater element’s connecting cable into the 
two marked terminals and tighten. Polarity of (heater 
element) connecting cable is not important.

»

If necessary: Install capillary tube on the thermo sensor 
using retainer clips.

»

To proceed further, follow the steps described above in 
section “Cleaning Coarse Strainer Cylinder Base.”

Содержание HeaterLine HL 12







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды