manualshive.com logo in svg

Huawei 9000 VCT V100R011, Руководство администратора, Страница: 28 / 204

Поделиться
Скачать
Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 28

l

Press the power switch on the rear panel to the 

OFF

 position.

The indicators on the front panel of the ViewPoint 9030 can be in different colors and blink at
different rates, thus indicating six states of the terminal. See 

Table 1-7

 and 

Table 1-8

.

Table 1-7

 Description of the power indicator

Indicator Status

Terminal Status

The indicator turns on in green.

The terminal is working properly.

The indicator turns off.

The terminal is powered off.

 

Table 1-8

 Description of the status indicator

Indicator Status

Terminal Status

The indicator turns on in orange.

l

The terminal is in the standby state.

l

The terminal is in sleep mode.

The indicator blinks in green at a
quick pace (at a rate of four times
per second).

The terminal is starting or upgrading.

The indicator blinks in green at a
slow pace (at a rate of once per
second).

The terminal responds to the remote control.

The indicator turns on in red.

A fault exists on the terminal.

 

When the terminal is powered off by pressing and holding 

 on the remote control the

operation must be confirmed. When the power switch on the front or rear panel is used to power
off the terminal, the operation does not need to be confirmed.

1.7 Entering and Coming out of the Sleep Mode

To reduce power consumption, the terminal can be configured to enter sleep mode after the
terminal has been in the idle state for a defined period of time.

Context

NOTE

Particular terminals may not support the sleep function. Contact the device provider if this function is
required.

The terminal can be woken up by performing any operation on the terminal. For example, the
terminal wakes up if there is an incoming call, an operation is performed on the remote control,
or the terminal is connected to the Web interface.

HUAWEI 9000 HD Video Terminal
Administrator Guide

1 Installation and Preparation

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

16

Содержание 9000 VCT V100R011













































































































































































































Отзывы:

Нет отзывов