hpmont : HD5L-4T5P5 Скачать руководство пользователя страница 95

Страница: 95 / 135

Chapter 7 Elevator Application Guidance

Shenzhen Hpmont Technology Co., Ltd.

―

HD5L Series Controller User Manual V1.4

7.2

Terminal MS Run Application

The elevator controller can calculate the motor present running direction (digital) and objective speed

(digital) according to the elevator control logic and send them to HD5L. HD5L receives the objective

speed of MS form and calculate the speed curve according to the S-curve parameter setting, then

control the motor to run.

Example:

A certain elevator with rated speed of 1.750m/s uses a controller in terminal MS control

(F00.05 = 2).

The brake and the contactor are controlled by the controller. The controller receives output signal of

HD5L at drive zero-speed running and controls the brake to close.

•

The inspection running is controlled by drive’s INS MS command, and the running speed is

obtained by MS terminal’s speed combination.

•

If use gearless permanent magnet syn. motor with SINCOS encoder, HD5L needs the SINCOS

encoder interface board with FD. HD5L receive the sine-cosine signal from the encoder as speed

signal, meanwhile HD5L can output pulse signal of no-FD or 2 - 126 odd-times FD to the elevator

controller without any weigh compensation device.

Control Part Connection

Figure 7-2 Terminal MS running connection

Sin A+, sin A-

Cos B+, cos B-

Sin C+, sin C-

Cos D+, cos D-

DI1

DI2

DI3

DI4

DI5

DI6

COM

RLY1

DO1

DO2

HD5L

Elevator

Controller

Controller enabled (EN)

Multi-speed 1 (MS1)

Multi-speed 2 (MS2)

Multi-speed 3 (MS3)

Controller fault

Controller is running

OUTA

OUTB

Controller is at
zero-speed running

Encoder

interface board

ERN1387

Содержание : HD5L-4T5P5








































































































































Результаты поиска

Содержание : HD5L-4T5P5

Отзывы:

hpmont : HD5L-4T5P5, Руководство пользователя, Страница: 95 / 135

Результаты поиска

Содержание : HD5L-4T5P5

Отзывы: