HP Storageworks 8100 - enterprise virtual array Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 408

background image

The following additional equipment is required to configure the MPX200:

•

B-series or C-series FC switch

•

Optical small form-factor pluggables (SFPs)
• FC ports, 8 Gb/s short-range SFP (AJ718A)
• FC ports, 4 Gb/s short-range SFP (A744B)
• 10-GbE ports, short-range SFP+ (455883–B21)

•

Optical FC cables, copper FC cables (direct-connect only)

•

Cat5e or Cat6 GbE network cables

•

Supported Direct Attach Copper 10GbE SFP+ Ethernet cables:
• HP ProCurve 10-GbE SFP+ 1m Direct Attach Cable (J9281B)
• HP ProCurve 10-GbE SFP+ 3m Direct Attach Cable (J9283B)
• HP ProCurve 10-GbE SFP+ 7m Direct Attach Cable (J9285B)
• HP ISS 10-GbE SFP+ 0.5m Direct Attach Cable (487649-B21)
• HP ISS 10-GbE SFP+ 1m Direct Attach Cable (487652-B21)
• HP ISS 10-GbE SFP+ 3m Direct Attach Cable (487655-B21)
• HP ISS 10-GbE SFP+ 7m Direct Attach Cable (487658-B21)
• Cisco 10-GbE SFP+ 3m Direct Attach Cable SFP-H10GB-CU3M (AP784A)
• Cisco 10-GbE SFP+ 5m Direct Attach Cable SFP-H10GB-CU5M (AP785A)
• Brocade 10-GbE SFP+ 1m Direct Attach Cable XBR-TWX-0101 (AP818A)
• Brocade 10-GbE SFP+ 3m Direct Attach Cable XBR-TWX-0301 (AP819A)
• Brocade 10-GbE SFP+ 5m Direct Attach Cable XBR-TWX-0501 (AP820A)

See

Chapter 4

and the SPOCK website at

http://www.hp.com/storage/spock

for FC switch model

support.

MPX200 configuration options

You can configure an EVA storage system for simultaneous connectivity to iSCSI and FC attached
hosts. Support for iSCSI to an EVA is provided through the MPX200 and an FC switch fabric port
(fabric attach) or the MPX200 directly connected to the EVA.

NOTE:

Directly connecting an MPX200 FC port and an EVA requires the EVA controller port to be set to
Direct.

Figure 1

illustrates an MPX200 single-blade fabric-attached configuration. This is the lowest-cost

configuration and is used when high availability for iSCSI hosts is not required.

MPX200 Multifunction Router

23

«
...
21
22
23
24
25
...
»

Содержание Storageworks 8100 - enterprise virtual array

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Storageworks 8100 - enterprise virtual array

Бренд: Dynex Страницы: 12

Бренд: CC&C Страницы: 24

Бренд: Nvidia Страницы: 62

Бренд: BenQ Страницы: 14

Бренд: VENOM Страницы: 2

Бренд: Acard Страницы: 34

Бренд: StarTech.com Страницы: 2

Бренд: Delta Страницы: 4

BasicXL BXL-NBT-AC01

Бренд: nedis Страницы: 16

Бренд: nedis Страницы: 30

Бренд: nedis Страницы: 2

Бренд: MSI Страницы: 162

PCM1000 - Cisco 10/100/1000 CARDBUS MOBILE NIC

Бренд: Linksys Страницы: 25

Бренд: Abocom Страницы: 2

QVI-W204-Y12-M AI N-VO

Бренд: Car Solutions Страницы: 18

Sub-Zero Series

Бренд: AIRSLED Страницы: 3

Бренд: Clint Страницы: 32

Бренд: ZJFKSDYX Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды