HP Storageworks 8100 - enterprise virtual array Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 408

background image

Yes

8

8M

50

No

7

4M

25

No

7

4M

20

No

6

2M

15

No

6

2M

10

No

5

1M

5

No

4

512K

2.5

No

2

128K

1 or less

Configuring an FCIP route

Step 1. Verify your system requirements

Verify that you have the following for both the local site and the remote site (see

Figure 65

on page 113):

•

HP StorageWorks MPX200 Multifunction Router 1–GbE Base Chassis or HP StorageWorks MPX200
Multifunction Router 10–1 GbE Base Chassis. Note that FCIP is currently supported only on MPX200
1 GbE ports.

•

HP Storage Works MPX200 Half Chassis FCIP License

•

Continuous Access EVA

•

EVA3000/5000 or EVA4x00/6x00/8x00 storage system

•

FC fabrics consisting of B-series or C-series switches

•

Cat 5e network cable, three per site (mgmt, (2) FCIP)

•

Optical small form-factor pluggable (SFP) transceiver and FC cable, two per site

•

MPX200 serial console cable adapter, Cat 5e network cable

Additional equipment for the local site and remote site (see

Figure 71

on page 118 and

Figure

73

, page 118) is as follows:

•

HP StorageWorks MPX200 Multifunction Router 1–GbE Upgrade Blade (MPX200 blade for re-
dundancy)
• Or HP StorageWorks MPX200 Multifunction Router 10–1 GbE Upgrade Blade. Note that FCIP

is currently supported only on MPX200 1 GbE ports.

• HP Storage Works MPX200 Full Chassis FCIP License

NOTE:

For the latest information about operating system and multipath software support, see SPOCK at the
website

http://www.hp.com/storage/spock

. You must sign up for an HP Passport to enable access.

Step 2. Pre-installation checklist

Before you begin the configuration process, contact your system administrator for the following
information for both sites:

MPX200 Multifunction Router

133

«
...
131
132
133
134
135
...
»

Содержание Storageworks 8100 - enterprise virtual array

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Storageworks 8100 - enterprise virtual array

D DPH-50U DPH-50U

Бренд: D-Link Страницы: 2

AirPlus DWL-810

Бренд: D-Link Страницы: 64

Бренд: D-Link Страницы: 39

Бренд: D-Link Страницы: 8

802.11g Wireless LAN USB Adapter DWL-G122

Бренд: D-Link Страницы: 43

AirPlusXtremeG DWL-G650

Бренд: D-Link Страницы: 20

Бренд: Uconnect Страницы: 3

Бренд: 3idee Страницы: 5

Бренд: 3idee Страницы: 5

Бренд: 3idee Страницы: 7

Бренд: UGREEN Страницы: 9

Бренд: Sena Страницы: 25

Бренд: KAT VR Страницы: 2

Redbooks ServeRAID-8s

Бренд: IBM Страницы: 58

Бренд: Skross Страницы: 2

Бренд: BASETech Страницы: 6

Бренд: Valor Страницы: 6

Quick Disconnect Feedder End Adapter Kits 4820G - 4995

Бренд: Bernard Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды