HP Performance Optimized Datacenter 20c Скачать руководство пользователя страница 34

Страница: 34 / 88

Removal and replacement procedures 34

Ventilation fan

The ventilation fan is located between the ECS cabinet and the transformer cabinet. The purpose of this fan

is to provide proper ventilation to the electrical components within the ECS and electrical cabinets.

Rittal SK 3243

You do not need any tools to remove and replace the ventilation fan.

Removing the Rittal SK 3243 ventilation fan

Open the ECS cabinet door.

Disconnect the fan wires.

Rotate the fan module counterclockwise to unseat it from the screwless spring terminal (1).

Pull the fan module forward to remove it (2).

Содержание Performance Optimized Datacenter 20c

























































































Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды

HP Performance Optimized Datacenter 20c, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды