HP Performance Optimized Datacenter 20c Скачать руководство пользователя

Страница: 28 / 88

Removal and replacement procedures 28

Fans

IT cooling fan

HP POD 20c fans operate at variable speeds to maintain the cold to hot aisle differential pressure and hot

aisle temperature setpoints that are programmed in the ECS.
The fan speed adjusts to maintain the programmed setpoints. Do not manually adjust the fan speed.

CAUTION:

Power must be removed from the fan power assembly before removing or replacing

a fan or fan bank.

CAUTION:

De-energize any additional working fans within the affected zone before replacing

the fan. De-energizing working fans reduces the IT cooling airflow within the zone. Take this into

consideration when deciding whether to continue operating IT equipment within the affected

zone. HP recommends powering down all of the IT in the zone.

IMPORTANT:

HP recommends leaving the fans in AUTO

mode during normal operation.

The HP POD 20c has 3 banks of 6 fans, for a total of 18 fans per zone. These fans circulate cool air from the

heat exchangers throughout the POD.

You need a screwdriver to remove and replace the IT cooling fan.

Removing the variable speed IT cooling fan

Take manual control of the fan speed in the affected zone from the ECS panel.

Set the fan speed to zero.

Содержание Performance Optimized Datacenter 20c

























































































Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды

HP Performance Optimized Datacenter 20c, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды