HP Performance Optimized Datacenter 20c Скачать руководство пользователя

Страница: 67 / 88

Removal and replacement procedures 67

Switches

ECS power switch

The ECS power switch is located on the ECS cabinet door.
You need a screwdriver to remove and replace the ECS power switch.

Removing the ECS power switch

Remove the ECS power switch (1).

Remove the four screws from the door interlock plate (2).

Remove the switch body from the interlock plate (3).

Disconnect the wires.

Replacing the ECS power switch

Reconnect the wires.

Insert the switch body into the interlock plate (1).

Insert the four screws into the door interlock plate (2).

Содержание Performance Optimized Datacenter 20c

























































































Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды

HP Performance Optimized Datacenter 20c, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды