HP Performance Optimized Datacenter 20c Скачать руководство пользователя

Страница: 78 / 88

Specifications 78

Fire alarm panel connections

The electrical layout of the fire alarm system is as described in the schematic drawing supplied with the HP
POD 20c.

Water specifications

The following table describes the chilled water system specifications for the HP POD 20c.

Feature

Specification

Facility input temperature to the HP POD
20c

12º to 24ºC (55º to 75ºF)

Max design pressure

1,034 kPa (150 psi)

HP POD 20c pressure drop

172.4 kPa (25 psi)

HP POD 20c water flow rate

454 lpm (120 gpm*)

Chilled water supply and return
connections

Two DIN PN16 DN80 flanges

*Measurement is in US gallons per minute.

Rack specifications

Standard HP POD 20c racks (AT978A)

Feature

Specification

U height

50U

Width

54.6 cm (21.5 in)

Depth

99 cm (39 in)*

Maximum load weight

1,360.7 kg (3,000 lb)

*This specification indicates the maximum clearance for the cold aisle. Equipment cannot exceed this measurement.

Thermal and air flow performance

Maximum thermal and air flow
performance parameters

HP POD 20c specification

Air temperature—Inlet to

rack-mounted components

Dependent on IT configuration and

chilled water inlet temperature

Chilled water temperature

C to 24

C (55

F to

Total rack-mounted component air
flow

Variable as required to maintain hot
aisle setpoint temperature and

dependent on IT configuration

Heat rejection capacity

300 kW

Environmental specifications

Feature

Specification

Operating temperature

-28ºC to 54ºC (-18ºF to 130ºF)

Non-operating temperature* -29ºC to 54ºC (-20ºF to 130ºF)

Содержание Performance Optimized Datacenter 20c

























































































Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды

HP Performance Optimized Datacenter 20c, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды