HP Performance Optimized Datacenter 20c Скачать руководство пользователя

Страница: 14 / 88

Illustrated parts catalog 14

Aisle clearances

Cold aisle clearance

The maximum protrusion of any installed IT component directly impacts the available cold aisle clearance for

removal and replacement of other IT components. Maximum component depth must follow the clear aisle
distance calculations. The following figure shows how to calculate this distance.

The maximum rack face-to-cold aisle wall distance is 39.5 inches. In the figure,

represents any protrusion

into the cold aisle starting from the rack face of the installed IT component (for example, the bezel).

represents cold aisle clearance. The cold aisle clearance dictates the maximum depth (

) of any installed IT

component. To find the maximum cold aisle clearance, calculate

100.33 cm (39.5 in) - X = Y

IMPORTANT:

As the value for

increases, the value for

decreases, which also decreases the

maximum depth allowed for an installed component.

Содержание Performance Optimized Datacenter 20c

























































































Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды

HP Performance Optimized Datacenter 20c, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды