HP Performance Optimized Datacenter 20c Скачать руководство пользователя

Страница: 62 / 88

Removal and replacement procedures 62

Replacing the EPO temperature sensors

Reconnect the replacement thermister coupling (1).

Secure the thermister with tie wraps (2).

Humidity sensor

The HP POD 20c contains one humidity sensor. It is located in the cold aisle in cooling zone 2.

You need a screwdriver to remove and replace the humidity sensor.

Removing the humidity sensor

Remove the four screws that secure the sensor cover (1), and then remove the cover (2).

Remove the two self-tapping screws (3).

Identify the sensor wires.

Disconnect the sensor wires.

Содержание Performance Optimized Datacenter 20c

























































































Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды

HP Performance Optimized Datacenter 20c, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды