HP Performance Optimized Datacenter 20c Скачать руководство пользователя

Страница: 64 / 88

Removal and replacement procedures 64

Temperature sensors (cold aisle)

The HP POD 20c contains three temperature sensors in the cold aisle. The temperature sensors are bolted to

the wall.

You need a Phillips-head screwdriver for installation.

Removing the cold aisle temperature sensor

Remove the four screws (1) that secure the cold-aisle temperature sensor cover, and then remove the
cover (2).

Label the cold-aisle temperature sensor wires or take a picture to remember which wires to reconnect

later.

Disconnect the wires.

Remove the two retaining screws, and then remove the cold-aisle temperature sensor housing from the

wall.

Содержание Performance Optimized Datacenter 20c

























































































Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды

HP Performance Optimized Datacenter 20c, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды