HP Performance Optimized Datacenter 20c Скачать руководство пользователя

Страница: 35 / 88

Removal and replacement procedures 35

Replacing the Rittal SK 3243 ventilation fan

Insert the fan module into the screwless spring terminal (1).

Rotate the fan module clockwise until it is seated (2).

Reconnect the fan wires.

Insert the ventilation fan into the ventilation fan cut-out hole.

Close the ECS cabinet door.

Filters

Heat exchanger air filters

There are two heat exchanger air filters per cooling zone for a total of six filters.

You do not need any tools to remove or replace the heat exchanger air filter.

Removing the heat exchanger air filter

Pull the locking tabs away from the filter to release it.

Содержание Performance Optimized Datacenter 20c

























































































Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды

HP Performance Optimized Datacenter 20c, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды