HP Performance Optimized Datacenter 20c Скачать руководство пользователя

Страница: 65 / 88

Removal and replacement procedures 65

Replacing the cold aisle temperature sensor

Reconnect the wires to the cold-aisle temperature sensor.

Reconnect the wires.

Re-attach the cold-aisle temperature sensor housing to the wall using the two retaining screws.

Replace the cold-aisle temperature sensor cover (1).

Replace the four screws that secure the cold-aisle temperature sensor cover (2).

Temperature sensors (hot aisle)

The HP POD 20c contains three temperature sensors in the hot aisle.

You need a screwdriver to remove and replace the hot aisle temperature sensors.

Содержание Performance Optimized Datacenter 20c

























































































Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды

HP Performance Optimized Datacenter 20c, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды