HP Performance Optimized Datacenter 20c Скачать руководство пользователя

Страница: 43 / 88

Removal and replacement procedures 43

Item Component

Indicator Color

Description

Source A available indicator

White

Indicates the EPO power status for main

power feed A

Source A wrong rotation indicator Red

Indicates the Source A power phase

rotation is incorrect

Source B wrong rotation indicator Red

Indicates the Source B power phase

rotation is incorrect

Source B available indicator

White

Indicates the EPO power status for main

power feed B

EPO shutdown indicator

Red

Indicates an EPO shutdown or alarm

situation

EPO armed indicator

White

Indicates that the EPO system is armed and

operational

EPO reset button

Blue

Resets the EPO system when pressed

EPO mode key control

—

Enables you to select the EPO mode.

EPO shutdown button

Red

Initiates a manual EPO event

Light test button

—

Tests all the EPO LED indicators when

pressed

EPO bypass mode indicator

Green

Indicates that the EPO shut down
functionality is bypassed

EPO test mode indicator

Yellow

Indicates that the EPO system is operating

in test mode or that an EPO cover is open

Main light switch

—

Turns power to the HP POD 20c lights off
and on

ECS power switch

—

Turns the main power to the 24V ECS

system off and on

Removing the ECS EPO LED indicators

Remove the screw from the mounting base (1).

Remove the contact block from the mounting base (2).

Содержание Performance Optimized Datacenter 20c

























































































Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды

HP Performance Optimized Datacenter 20c, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды