manualshive.com logo in svg

HP Integrity NonStop NS-series, Руководство по эксплуатации

Поделиться
Скачать
HP Integrity NonStop NS-series Скачать руководство пользователя страница 95

Communications Subsystems: Monitoring and 
Recovery

HP Integrity NonStop NS-Series Operations Guide — 529869-005

6- 13

Recovery Operations for Communications

Subsystems

Recovery Operations for Communications 
Subsystems 

Some general troubleshooting guidelines are:

•

Examine the contents of the event message log for the subsystem. For example, 
the WAN subsystem or Kernel subsystem might have issued an event message 
that provides information about the process failure. Event messages returned by 
the WAN subsystem and SWAN concentrator are described in the WANMGR and 
TRAPMUX sections of the 

Operator Messages Manual, 

respectively.

•

HP provides a comprehensive library of troubleshooting guides for the 
communications subsystems. Attempt to analyze the problems and restart the 
process or object using the commands described in the appropriate manual listed 
in 

Related Reading

 on page 6-13. If you are unable to start a required process or 

object, contact your service provider.

Related Reading

For more information about monitoring and performing recovery operations for 
communications subsystems, see the manuals listed in 

Table 6-1

. The appropriate 

manual to use depends on how your system is configured. 

For example, if a process is configured using the SCF interface to the WAN subsystem 
and then reconfigured with the SCF interface to another subsystem, only the SCF 
interface to the other subsystem would provide current information about the 
configuration. The SCF interface to the WAN subsystem would provide only 
information about the configuration before it changed. 

  

Table 6-1. Related Reading for Communications Lines and Devices

(page 1 of 2)

For Information 
About...

Refer to...

General information 
about communications 
subsystems

Introduction to Networking for HP NonStop NS-Series Servers

Using SCF to monitor 
generic processes

SCF Reference Manual for the Kernel Subsystem

Using SCF to monitor 
the SLSA subsystem as 
well as Ethernet 
addressable devices, 
such as ServerNet 
adapters

LAN Configuration and Management Manual

 

Содержание Integrity NonStop NS-series











































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды