HP Integrity NonStop NS-series Скачать руководство пользователя страница 181

Страница: 181 / 266

Starting and Stopping the System

HP Integrity NonStop NS-Series Operations Guide — 529869-005

15- 5

Starting a System

If any components fail during any of the power shutdowns, see

Components

Fail When Testing the Power

on page 15-19.

If you have a UPS installed, switch off the UPS outputs.

5. If you have a UPS installed, check that the UPS is fully charged. Then, test the

UPS by turning off both circuit breakers.

6. Log on to the OSM Low-Level Link.

7. Select

System Discovery

8. Double-click the System.

9. Double-click each Group 40

; for example, Group 400.

10. Check that the logical processors are displayed.

11. Double-click each Group 1

; for example, Group 100.

12. For each Group 1

, check that module 2 and module 3 are displayed.

13. If any of these components are not yet displayed, wait before you start the system.

14. After the system is powered on, you must wait 5 minutes before starting the

system.

15. You can now start your system as described in

Starting a System

on page 15-5.

Starting a System

Use the OSM Low-Level Link to start a system. Starting a system includes a system
load from disk into the memory of one processor; followed by the reload of the
remaining processors.

Loading the System

Perform a system load to load the NonStop operating system.

Alerts

•

All processors in the system must be in a halted state before you perform a system
load.

•

To perform processor dumps during a system load, see the considerations in

System Load to a Specific Processor

on page 15-6.

Normal System Load

Normally, you initiate the system load as described in

Performing a System Load

page 15-9. When you choose this method:

Содержание Integrity NonStop NS-series











































































































































































































































































Результаты поиска

Содержание Integrity NonStop NS-series

Отзывы:

Бренды по названию

Популярные бренды

HP Integrity NonStop NS-series, Руководство по эксплуатации

Результаты поиска

Содержание Integrity NonStop NS-series

Отзывы:

Бренды по названию

Популярные бренды