manualshive.com logo in svg

HP Integrity NonStop NS-series, Руководство по эксплуатации

Поделиться
Скачать
HP Integrity NonStop NS-series Скачать руководство пользователя страница 195

Starting and Stopping the System

HP Integrity NonStop NS-Series Operations Guide — 529869-005

15 -19

System Does Not Appear to Be Powered On

System Does Not Appear to Be Powered On

If AC power is being supplied to the server and the fans are turning but the server still 
does not appear to be powered, the server might be running internal tests. Wait 
several minutes (at least 10 minutes for large configurations). If the server is still not 
powered on after this time and you cannot determine the cause of the problem:

•

Check your site’s circuit breakers.

•

Plug in another device into the PDU that powers the LSU to check the power for 
that PDU.

Green LED Is Not Lit After POSTs Finish

It can take several minutes for the green LEDs on all system components to light:  

1. Wait for the POSTs to finish.  It might take as long as 10 minutes for all system 

components.  

2. If the green LEDs still do not light:

a. Check that AC power cords and component power cords are properly 

connected.

b. If one green LED still does not light, a system component might have failed its 

POST.  

3. If you cannot determine the cause of the problem, contact your service provider.  

Amber LED on a Component Remains Lit After the POST 
Finishes

A fault might have been detected, or the component might not have been successfully 
initialized and configured. Contact your service provider.

Components Fail When Testing the Power 

If a component fails when testing the power, the possible causes are listed in 
descending order of probability:

•

The component is plugged in improperly.

Check the connection between each component power cord and PDU, and check 
the AC power receptacle to which the server power cord is connected. If 
necessary, unplug and plug each cord in again to ensure that it is seated properly.

•

A power cord is defective.

•

A component power supply is defective.

•

A fuse is defective.

•

The UPS, if installed, is not fully charged.

Содержание Integrity NonStop NS-series











































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды