manualshive.com logo in svg

HP Integrity NonStop NS-series, Руководство по эксплуатации

Поделиться
Скачать
HP Integrity NonStop NS-series Скачать руководство пользователя страница 212

Creating Startup and Shutdown Files

HP Integrity NonStop NS-Series Operations Guide — 529869-005

16 -12

Startup File Examples

Startup File Examples

You can implement the system startup sequence with a collection of startup files, each 
with a specific purpose. HP recommends that you invoke the startup files in this order: 

1. Startup file for the system, to be invoked after the CIIN file is invoked

2. Startup files for the system software

3. Startup files for the subsystems

4. Startup files for the communications lines

5. Startup files for the applications

See 

Section 15, Starting and Stopping the System

 for detailed instructions on the 

startup procedure. For information about automating disk processes upon startup, see 
the 

Integrity

 

NonStop NS-Series Planning Guide

. 

System Startup File

The following example shows a partial command file that starts up the system software 
and invokes other startup files.

After the commands in the CIIN file have been executed and the initial system startup 
sequence is complete, the local operator invokes this file by entering the following 
TACL command: 

> OBEY $SYSTEM.STARTUP.STRTSYS

Comment -- This is $SYSTEM.STARTUP.STRTSYS

comment -- Start the server for labeled tape processing.

ZSERVER / NAME $ZSVR, NOWAIT, PRI 145, CPU 0 / 1
ZSERVER / NAME $ZSVR, NOWAIT, PRI 145, CPU 1 / 0
MEDIACOM ALTER TAPEDRIVE *, NLCHECK OFF

Comment -- If you have used SCF to start a persistent Subsystem 
Comment -- Control Process (SCP) process pair, you do not need an 
Comment -- explicit SCP command to start $ZNET, unless you load the 
Comment -- system from a different CONFIG file.  
Comment -- All SCF commands are routed through the SCP process.  $ZNET 
Comment -- routes each request to the appropriate communication
Comment -- management process (such as Expand or SNAX).

Comment -- If you have not configured SCP as a persistent generic 
Comment -- process, remove the commenting from the following SCP 
Comment -- command and start SCP as a nonpersistent process pair.  
Comment -- SCP / NAME $ZNET, NOWAIT, PRI 199, TERM $ZHOME, OUT $ZHOME, & 
Comment -- CPU 0/1; AUTOSTOP -1

Note.

Examples and sample programs are for illustration only and might not be suited for your 

particular purpose. HP does not warrant, guarantee, or make any representations regarding 
the use or the results of the use of any examples or sample programs in any documentation. 
You must verify the applicability of any example or sample program before placing the software 
into production use. For more information, see 

Example Command Files

 on page 16-4.

Содержание Integrity NonStop NS-series











































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды