manualshive.com logo in svg

HP Integrity NonStop NS-series, Руководство по эксплуатации

Поделиться
Скачать
HP Integrity NonStop NS-series Скачать руководство пользователя страница 185

Starting and Stopping the System

HP Integrity NonStop NS-Series Operations Guide — 529869-005

15- 9

Starting Other System Components

Starting Other System Components

HP recommends that you bring your system up in stages, verifying each stage, to 
facilitate recovery if any step fails. When the system starts, many individual devices, 
processes, applications, and communications lines start automatically, but others might 
need to be started using start up files. Follow your site’s procedures for starting your 
applications.  

•

Many processes are configured by default to be started automatically by the $ZPM 
persistence monitor.  These processes include the Kernel subsystem, SLSA 
subsystem, storage subsystem, and WAN subsystem. The manager processes for 
these subsystem start disks, SWAN concentrators, some LAN devices, and many 
processes.

•

You can use SCF to configure other processes, typically monitor or manager 
processes, to start automatically as generic processes when the system starts.  
For example, you can use the SCF interface to the Kernel subsystem to add these 
processes to the system configuration database:

°

$ZEXP, the Expand manager process 

°

$ZPMON, the OSS monitor process   

For more information about configuring generic processes to start automatically, 
refer to the documentation in 

Related Reading

 on page 15-24.

•

You can include commands in startup command files that you invoke from a TACL 
prompt or another startup file. For some techniques to make startup command files 
run as efficiently as possible, refer to 

Writing Efficient Startup and Shutdown 

Command Files

 on page 16-9.   

Performing a System Load 

To perform a normal system load:

1. Verify that all processors are halted as described in 

Stopping the System

 on 

page 15-16. All processors in the system must be halted before you initiate a 
system load. 

2. Log on to the OSM Low-Level Link.

3. From the OSM Low-Level Link toolbar, click 

Start system

.  

4. If you initiate a system load while processors are running, a message appears 

asking whether you want to proceed.  If you click Yes, all the processors are 
halted, then the system load begins. 

Содержание Integrity NonStop NS-series











































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды