manualshive.com logo in svg

HP Integrity NonStop NS-series, Руководство по эксплуатации

Поделиться
Скачать
HP Integrity NonStop NS-series Скачать руководство пользователя страница 45

Determining Your System Configuration

HP Integrity NonStop NS-Series Operations Guide — 529869-005

2 -9

Displaying SCF Configuration Information for

Subsystems

To display information about a particular device:

> SCF LISTDEV TYPE 

n

where 

n

 is a number for the device type. For example, if 

n

 is 3, the device type is 

disks. For the \MS9 system, entering LISTDEV TYPE 3 would display information for 
$DATA6, $DATA5, $DATA4, $DATA3, $DATA2, $DATA1, and $DATA.

To display information for a given subsystem:

> SCF LISTDEV 

subsysname

where 

subsysname

 is the logical name of a subsystem; for example, $ZZKRN for the 

Kernel subsystem.

Displaying SCF Configuration Information for Subsystems 

The following tables give some of the SCF commands that display configuration 
information for objects controlled by subsystems that are common to most Integrity 
NonStop NS-series systems. The examples use the SCF ASSUME command to make 
a given subsystem the current default object for gathering information.

TCP/IP Subsystem

These examples are based on a TCP/IP process named $ZTCO. Before using the 
commands listed in 

Table 2-2

, type this command to make the TCP/IP subsystem the 

default object:

> SCF ASSUME PROCESS $ZTCO

Integrity NonStop servers support two versions of TCP/IP—NonStop TCP/IPv6 and 
NonStop TCP/IP. When you use the SCF LISTDEV and INFO commands, all current 
TCP/IP processes are displayed. For more information, refer to the 

TCP/IPv6 

Configuration and Management Manual 

and

 

the 

TCP/IP Configuration and 

Management Manual.

Table 2-2. Displaying Information for the TCP/IP Subsystem ($ZTCO)

To Display Information About These 
Configured Objects

 Enter This Command

All TCP/IP devices

LISTDEV TCPIP

Detailed information about the TCP/IP 
subsystem manager

INFO, DETAIL

All SUBNET names

INFO SUBNET *

All ROUTE names

INFO ROUTE *

Содержание Integrity NonStop NS-series











































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды