manualshive.com logo in svg

HP Integrity NonStop NS-series, Руководство по эксплуатации

Поделиться
Скачать
HP Integrity NonStop NS-series Скачать руководство пользователя страница 124

Processors and Components: Monitoring and 
Recovery

HP Integrity NonStop NS-Series Operations Guide — 529869-005

9- 12

Reloading a Single Processor on a Running Server

is one of these:

cpu

 

cpu-cpu

cpu

 

is the processor number, an integer from 0 through 15. 

cpu-cpu

is two processor numbers separated by a hyphen, 
specifying a range of processors. In a range 
specification, the first processor number must be 
less than the second.

option

is one of these:

NOSWITCH
[PRIME|NOPRIME]

fabric

OMITBLADE [A|B|C]

$volume [.sysnn.osdir]

NOSWITCH

specifies that, when a processor is reloaded, there is no default 
autoswitch of controller ownership to the configured primary processor.

[PRIME|NOPRIME]

Sets up the logical processor for the reload operation. NOPRIME is the 
default.

fabric

specifies whether the X fabric or Y fabric is used for the transfer of the 
operating system image to the processor during the RELOAD 
operation.

0 = X fabric
1 = Y fabric

The default option is the X fabric.

OMITBLADE [A|B|C]

The PE on the selected Blade Element will not be reloaded when other 
PEs in that logical processor are reloaded. If you do not provide an 
argument (A or B or C) the system will choose a Blade Element to 
omit.

$volume [.sysnn.osdir]

specifies a volume other than $SYSTEM where the operating system 
image (

sysnn.osdir

) to be used for reloading the processor is 

located.

Depending on your requirements, this specification could take the form 
of 

$volume

 or 

$volume.sysnn.osdir

 or 

sysnn.osdir 

or 

osdir

.

Содержание Integrity NonStop NS-series











































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды