manualshive.com logo in svg

HP Integrity NonStop NS-series, Руководство по эксплуатации

Поделиться
Скачать
HP Integrity NonStop NS-series Скачать руководство пользователя страница 26

Introduction to Integrity NonStop NS-Series 
Operations

HP Integrity NonStop NS-Series Operations Guide — 529869-005

1 -2

When to Use This Section

When to Use This Section

This section introduces system hardware operations for Integrity NonStop NS-series 
servers. It provides an introduction to the other sections in this guide. 

Understanding the Operational Environment

To understand the operational environment:

•

If you are already familiar with other NonStop systems, see 

Appendix A, 

Operational Differences Between Systems Running G-Series and H-Series RVUs

. 

•

For a brief introduction to the system organization and the location of system 
components in an Integrity NonStop server, see 

Section 2, Determining Your 

System Configuration

.

•

For information about various software tools and utilities you can use to perform 
system operations on an Integrity NonStop server, see 

Appendix B, Tools and 

Utilities for Operations

. 

What Are the Operator Tasks?

The system operations described in this guide include:

•

Monitoring the system and performing recovery operations

•

Preparing for and recovering from power failures

•

Stopping and powering off the system

•

Powering on and starting the system

•

Performing preventive maintenance

•

Operating disk drives and tape drives

•

Responding to spooler problems

Monitoring the System and Performing Recovery Operations   

Checking for indications of potential system problems by monitoring the system is part 
of the normal system operations routine. You perform recovery operations to restore a 
malfunctioning system component to normal use. Most recovery procedures for 
Integrity NonStop servers can be performed online. Monitoring the status of all system 
components and performing recovery operations are described in:

•

Section 3, Overview of Monitoring and Recovery

•

Section 4, Monitoring EMS Event Messages

•

Section 5, Processes: Monitoring and Recovery

•

Section 6, Communications Subsystems: Monitoring and Recovery

•

Section 7, ServerNet Resources: Monitoring and Recovery

•

Section 8, I/O Adapters and Modules: Monitoring and Recovery

•

Section 9, Processors and Components: Monitoring and Recovery

Содержание Integrity NonStop NS-series











































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды