manualshive.com logo in svg

HP Integrity NonStop NS-series, Руководство по эксплуатации

Поделиться
Скачать
HP Integrity NonStop NS-series Скачать руководство пользователя страница 100

ServerNet Resources: Monitoring and Recovery

HP Integrity NonStop NS-Series Operations Guide — 529869-005

7 -4

System I/O ServerNet Connections

Integrity NonStop NS1000 ServerNet Connectivity

ServerNet connections between I/O devices and processors depend on whether the 
Integrity NonStop NS1000 system has an IOAM enclosure or VIO enclosures. For 
more information on Integrity NonStop NS1000 systems, see the 

NonStop NS1000 

Planning Guide

, 

NonStop NS1000 Hardware Installation Manual

, or the 

Versatile I/O 

(VIO) Manual

.

System I/O ServerNet Connections

For Integrity NonStop NS16000 systems, ServerNet connections to the system I/O 
devices (storage disk and tape drive as well as Ethernet communication to networks) 
radiate out from the p-switches for both the X and Y ServerNet fabrics.

ServerNet cables connected to the p-switch PICs in slots 10 through 13 come from the 
LSUs and processors. Cables connected to the PICs in slots 4 though 9 connect to 
one or more IOAM enclosures or to NonStop S-series I/O enclosures equipped with 
IOMF2 CRUs. 

Figure 7-3

 shows the connections to the PICs in a fully populated 

p-switch.

For Integrity NonStop NS14000 systems, see 

Integrity NonStop NS14000 ServerNet 

Connectivity

 on page 7-3. Like NS14000 systems, Integrity NonStop NS1000 systems 

use 4PSEs to provide ServerNet connections between I/O devices and processors. 
However, there are no LSUs; the 4PSEs connect directly to the Blade Elements. For 
more information, see the 

NonStop NS1000 Hardware Installation Manual

.

Monitoring the Status of the ServerNet Fabrics

The ServerNet fabrics provide the communication paths used for interprocessor 
messages, for communication between processors and I/O devices, and (in the case of 

Figure 7-3. I/O Connections to the PICS in a P-Switch

Содержание Integrity NonStop NS-series











































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды