manualshive.com logo in svg

HP Integrity NonStop NS-series, Руководство по эксплуатации

Поделиться
Скачать
HP Integrity NonStop NS-series Скачать руководство пользователя страница 77

HP Integrity NonStop NS-Series Operations Guide — 529869-005

5 -1

5

 

Processes: Monitoring and 
Recovery

When to Use This Section

 on page 5-1

Types of Processes

 on page 5-1

System Processes on page 5-1

I/O Processes (IOPs)

 on page 5-2

Generic Processes

 on page 5-2

Monitoring Processes

 on page 5-3

Monitoring System Processes on page 3

Monitoring IOPs

 on page 4

Monitoring Generic Processes

 on page 4

Recovery Operations for Processes

 on page 5-6

Related Reading

 on page 5-6

When to Use This Section

This section provides basic information about the different types of processes for 
Integrity NonStop servers. It gives a brief example of monitoring each type of process 
and provides information about the commands available for recovery operations. 

Types of Processes

Three types of processes are of major concern to a system operator of an Integrity 
NonStop NS-series server:

•

System processes

•

I/O processes (IOPs)

•

Generic processes

System Processes

A system process is a privileged process that is created during system load and exists 
continuously for a given configuration for as long as the processor remains operable. 
Examples of system processes include the memory manager, the monitor, and the I/O 
control processes. 

Содержание Integrity NonStop NS-series











































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды