manualshive.com logo in svg

HP Integrity NonStop NS-series, Руководство по эксплуатации

Поделиться
Скачать
HP Integrity NonStop NS-series Скачать руководство пользователя страница 122

Processors and Components: Monitoring and 
Recovery

HP Integrity NonStop NS-Series Operations Guide — 529869-005

9- 10

Halting One or More Processors

The best manual recovery operation for your processor halt scenario depends on the 
type of halt. You should record the halt information (as described in 

Identifying 

Processor Problems

 on page 9-7), and contact your service provider to help you 

determine the appropriate course of action.

This section describes the various options for 

Dumping a Processor to Disk

 and 

Reloading a Single Processor on a Running Server

 that you might be directed to use.

Halting One or More Processors

To place a selected processor or processors in a halt state and set the status and 
registers of the processor or processors to an initial state: 

1. Log on to the OSM Low-Level Link.

2. On the toolbar, click 

Processor Status

 button.

3. In the Processor Status dialog box, select the processor to be halted or select all 

the processors to halt all of them.

4. Select 

Processor Actions>Halt

.

5. Click 

Perform action

.

6. A message box appears and asks whether you are sure you want to perform a halt 

on the selected processor or processors. Click 

OK

.

Reloading a Single Processor on a Running Server

Sometimes one or more processors in a running server are not operating. For 
information on how to determine whether a processor is operating, see 

Monitoring 

Processor Performance Using ViewSys

 on page 9-7. 

Unlike NonStop S-series, you don’t always have to wait until you dump the processor 
before reloading it. This section describes how, when appropriate, to exclude the 
processor element (PE) from one NonStop Blade Element during the reload operation, 
so you can get the rest of the processor running, take the dump, then reintegrate the 
PE back into the running processor.

After you have determined that a processor is not operating, check that the processor 
is halted. If it needs to be halted, see 

Halting One or More Processors

 on page 9-10).

Collect information about the reason for the halt (as described in 

Identifying Processor 

Problems

 on page 9-7) to send to your service provider along with the dump file. In the 

Low-Level Link Processor Status dialog box, write down the halt code and status 
message for the processor.

Your options for reloading a processor on a running server are:

•

Using TACL RELOAD to Perform Reload on page 9-11

•

Using the OSM Service Connection to Perform Reload on page 9-13

Following the reload, if TFDS is not configured to take the dump automatically, you can 
perform a dump of the omitted PE while normal operations resume on the reloaded 
PEs within that logical processor. See the 

Dumping a Processor to Disk

 on page 9-15.

Содержание Integrity NonStop NS-series











































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды