manualshive.com logo in svg

HP Integrity NonStop NS-series, Руководство по эксплуатации

Поделиться
Скачать
HP Integrity NonStop NS-series Скачать руководство пользователя страница 145

Disk Drives: Monitoring and Recovery

HP Integrity NonStop NS-Series Operations Guide — 529869-005

10 -11

Identifying Disk Drive Problems

Identifying Disk Drive Problems

For recovery operations, refer to 

Recovery Operations for Disk Drives

 on page 10-12.

Internal SCSI Disk Drives

The most common disk drive problems on a NonStop S-series server include: 

•

Space problems such as full disks or free-space fragmentation

•

Stopped disks

•

Performance problems 

•

Defective tracks or sectors

M8xxx Fibre Channel Disk Drives

The most common disk problems on an Integrity NonStop NS-series server are intm-
errors-exceeded and slow-IOs-threshold-exceeded errors on the Fibre Channel loop. 

Such errors are often normal. However, if they cause problems on a Fibre Channel 
loop, power the affected disk down and up again. This procedure can solve the 
problem temporarily. 

Unless you are a qualified service provider, you cannot perform any physical actions 
on disk drives. However, operators can use OSM and SCF commands. 

Table 10-2. Possible Causes of Common Disk Drive Problems

Problems

Possible Symptoms

Disk is full or does not have enough space.

Error 43 (unable to obtain disk space for file 
extent) occurs. 

If the disk is full, an application might go down.

Disk free space is fragmented.

One disk in a mirrored pair is down.

The storage subsystem generates an event 
message but the application continues to run.

An unmirrored disk is down, or both disks 
in a mirrored pair are down.

Users report access problems, applications go 
down, and the storage subsystem generates 
event messages.

Performance problems occur due to path 
switches or a cache size that is too small.

Users report poor application performance.

Defective tracks or sectors exist.

Output from SCF INFO DISK, BAD command 
indicates unspared defective sectors.

Disk errors exceed a certain limit.

Intm-errors-exceeded message

Slow I/O operations exceed a certain limit.

Slow-IOs-threshold-exceeded message

Содержание Integrity NonStop NS-series











































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды