HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 112

Страница: 112 / 306

104

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation selected-port minimum 3

Related commands

link-aggregation selected-port maximum

port link-aggregation group

Use

port link-aggregation group

to assign an Ethernet interface to an aggregation group.

Use

undo port link-aggregation group

to remove the Ethernet interface from the aggregation

group to which it belongs.

Syntax

port link-aggregation group number

undo port link-aggregation group

Default

An Ethernet interface does not belong to any aggregation group.

Views

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Parameters

number

: Specifies an aggregation group by its aggregate interface number in the range of 1 to 1024.

Usage guidelines

An Ethernet interface can belong to only one aggregation group.

Examples

# Assign Layer 2 Ethernet interface GigabitEthernet 1/0/1 to Layer 2 aggregation group 1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port link-aggregation group 1

reset counters interface

Use

reset counters interface

to clear statistics for the specified aggregate interfaces.

Syntax

reset counters interface

[

bridge-aggregation

[

interface-number

] ]

Views

User view

Predefined user roles

network-admin

Parameters

bridge-aggregation

: Specifies Layer 2 aggregate interfaces.

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды