manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Справочник по командам

Поделиться
Скачать
HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 101

 

93 

Views 

Layer 2 Ethernet interface view 

Predefined user roles 

network-admin 

Usage guidelines 

When LACP is operating in passive mode on a local member port and its peer port, both ports cannot 
send LACPDUs. When LACP is operating in active mode on either end of a link, both ports can send 
LACPDUs. 

This command takes effect only on member ports of dynamic aggregation groups. 

Examples 

# Configure LACP to operate in passive mode on GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] lacp mode passive 

lacp period short 

Use 

lacp period short

 to set the short LACP timeout interval (3 seconds) on an interface. 

Use 

undo lacp period

 to restore the default. 

Syntax 

lacp period short 

undo lacp period 

Default 

The LACP timeout interval is the long timeout interval (90 seconds) on an interface. 

Views 

Layer 2 Ethernet interface view 

Predefined user roles 

network-admin 

Examples 

# Set the short LACP timeout interval (3 seconds) on GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] lacp period short 

lacp system-priority 

Use 

lacp

 

system

-

priority

 to set the system LACP priority. 

Use 

undo

 

lacp

 

system-priority

 to restore the default. 

Syntax 

lacp

 

system-priority

 

system-priority

 

undo

 

lacp

 

system-priority

 

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды