HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 56

Страница: 56 / 306

Line protocol state: UP (spoofing)

Description: NULL0 Interface

Bandwidth: 0kbps

Maximum transmission unit: 1500

Internet protocol processing: Disabled

Physical: NULL DEV

Last clearing of counters: Never

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Input: 0 packets, 0 bytes, 0 drops

Output: 0 packets, 0 bytes, 0 drops

# Display brief information about interface Null 0.

<Sysname> display interface null 0 brief

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface Link Protocol Primary IP Description

NULL0 UP UP(s) -- aaaaaaaaaaaaaaaaaaaaaaaaaaa

# Display brief information about interface Null 0, including the complete description of the null
interface.

<Sysname> display interface null 0 brief description

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface Link Protocol Primary IP Description

NULL0 UP UP(s) -- aaaaaaaaaaaaaaaaaaaaaaaaaaaaa

aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa

For the command output, see

Table 11

and

Table 12

Related commands

•

interface

null

•

reset counters interface null

interface loopback

Use

interface loopback

to create a loopback interface and enter loopback interface view.

Use

undo interface loopback

to remove a loopback interface.

Syntax

interface loopback

interface-number

undo interface loopback

interface-number

Default

No loopback interface exists.

Views

System view

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды