HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 9

Страница: 9 / 306

Ethernet interface commands

Common Ethernet interface commands

bandwidth

Use

bandwidth

to configure the expected bandwidth of an interface.

Use

undo bandwidth

to restore the default.

Syntax

bandwidth

bandwidth-value

undo bandwidth

Default

The expected bandwidth (in kbps) is the interface baud rate divided by 1000.

Views

Ethernet interface view

Predefined user roles

network-admin

Parameters

bandwidth-value

: Specifies the expected bandwidth in the range of 1 to 400000000 kbps.

Usage guidelines

The expected bandwidth of an interface affects the following items:

•

Bandwidth assignment with CBQ. For more information, see

ACL and QoS Configuration

Guide

Examples

# Set the expected bandwidth of interface GigabitEthernet 1/0/1 to 1000 kbps.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] bandwidth 1000

Related commands

speed

default

Use

default

to restore the default settings for an Ethernet interface.

Syntax

default

Views

Ethernet interface view

Predefined user roles

network-admin

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды