HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 191

Страница: 191 / 306

183

Examples

# Configure VLAN 100 as the PVID of the trunk port GigabitEthernet 1/0/1, and assign
GigabitEthernet 1/0/1 to VLAN 100.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port link-type trunk

[Sysname-GigabitEthernet1/0/1] port trunk pvid vlan 100

[Sysname-GigabitEthernet1/0/1] port trunk permit vlan 100

Related commands

•

port

link-type

•

port trunk permit vlan

MAC-based VLAN commands

display mac-vlan

Use

display mac-vlan

to display MAC-to-VLAN entries.

Syntax

display mac-vlan

{

all

dynamic

mac-address

mac-address

[

mask

mac-mask

] |

static

vlan

vlan-id

}

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

all

: Specifies all MAC-to-VLAN entries.

dynamic

: Specifies dynamically configured MAC-to-VLAN entries.

mac-address mac-address

: Specifies the MAC address in the MAC-to-VLAN entry.

mask

mac-mask

: Specifies the mask for matching MAC addresses in MAC-to-VLAN entries.

static

: Specifies statically configured MAC-to-VLAN entries.

vlan

vlan-id

: Specifies the VLAN in MAC-to-VLAN entries. The value range for the

vlan-id

argument

is 1 to 4094.

Examples

# Display all MAC-to-VLAN entries.

<Sysname> display mac-vlan all

The following MAC VLAN entries exist:

State: S - Static, D - Dynamic

MAC address Mask VLAN ID Dot1q State

0008-0001-0000 FFFF-FF00-0000 5 3 S

0002-0001-0000 FFFF-FFFF-FFFF 5 3 S&D

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды