HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 93

Страница: 93 / 306

<Sysname> display link-aggregation load-sharing mode interface bridge-aggregation 10

Bridge-Aggregation10 Load-Sharing Mode:

destination-mac address source-mac address

Table 19 Command output

Field Description

Link-Aggregation Load-Sharing
Algorithm

Per-flow load sharing algorithm for Ethernet link aggregation.

By default, this field displays

Default

. If you have configured the

load sharing algorithm, this field displays the configured
algorithm.

Link-Aggregation Load-Sharing Seed

Per-flow load sharing algorithm seed for Ethernet link
aggregation.

By default, this field displays

Default

. If you have configured the

load sharing algorithm seed, this field displays the configured
seed.

Link-Aggregation Load-Sharing Mode

Global link-aggregation load sharing mode.

•

By default, this field displays the link-aggregation load
sharing modes for Layer 2 traffic and Layer 3 traffic.

•

If you have set the global link-aggregation load sharing
mode, this field displays the configured mode.

Bridge-Aggregation10 Load-Sharing
Mode

Link-aggregation load sharing mode of Layer 2 aggregation group
10.

•

By default, this field displays the global link-aggregation load
sharing modes.

•

If you have set a link-aggregation load sharing mode for this
aggregation group, this field displays the configured mode.

Layer 2 traffic: packet type-based
sharing

Default link-aggregation load sharing mode for Layer 2 traffic. In
this sample output, Layer 2 traffic is load shared based on the
packet type.

Layer 3 traffic: packet type-based
sharing

Default link-aggregation load sharing mode for Layer 3 traffic. In
this sample output, Layer 3 traffic is load shared based on the
packet type.

destination-mac address, source-mac
address

User-configured link-aggregation load sharing mode. In this
sample output, traffic is load shared based on source and
destination MAC addresses.

Related commands

•

link-aggregat

on global load-sharing algorithm

•

link-aggregation global load-sharing mode

•

link-aggregation global load-sharing seed

•

link-aggregation load-sharing mode

display link-aggregation member-port

Use

display link-aggregation member-port

to display detailed link aggregation information for the

specified member ports.

Syntax

display link-aggregation member-port

[

interface-list

]

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды