manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Справочник по командам

Поделиться
Скачать
HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 39

31 

rate. For example, the value range for this argument is 0 to 1488100 on a GE interface and 0 to 
59524000 on a 40-GE interface. 

kbps  max-kbps

: Specifies the maximum number of kilobits of multicast traffic that the Ethernet 

interface can forward per second. The value range for this argument (in kbps) is 0 to the maximum 
interface rate.  

Usage guidelines 

You can use the multicast storm suppression function to limit the size of multicast traffic on an 
interface. When the multicast traffic on the interface exceeds this threshold, the system drops 
packets until the traffic drops below this threshold.  

Both the 

storm-constrain

 and 

multicast-suppression

 can suppress multicast storm on a port. The 

storm-constrain

 command uses software to suppress traffic, and it affects the device performance 

to a certain extent. The 

multicast-suppression

 command uses the chip to physically suppress 

multicast traffic, and it has less influence on the device performance than the 

storm-constrain

 

command. Do not configure the 

storm constrain

 command and the 

multicast-suppression

 

command at the same time. Otherwise, the traffic suppression result is not determined.  

When you configure the suppression threshold in kbps, the actual suppression threshold might be 
different from the configured one as follows: 

•

 

If the configured value is smaller than 64, the value of 64 takes effect. 

•

 

If the configured value is greater than 64 but not an integer multiple of 64, the integer multiple of 
64 that is greater than and closest to the configured value takes effect. 

To determine the suppression threshold that takes effect, see the prompts on the device.  

Examples 

# Set the multicast storm suppression threshold to 10000 kbps on GigabitEthernet 1/0/1. 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] multicast-suppression kbps 10000 

The actual value is 10048 on port GigabitEthernet1/0/1 currently. 

Related commands 

•

 broadcast-suppression 

•

 unicast-suppression 

port bridge enable 

Use 

port bridge enable

 to enable bridging on a Layer 2 Ethernet interface. 

Use 

undo port bridge enable

 to disable bridging on a Layer 2 Ethernet interface. 

Syntax 

port bridge enable 

undo port bridge enable 

Default 

Bridging is disabled on Layer 2 Ethernet interfaces. 

Views 

Layer 2 Ethernet interface view 

Predefined user roles 

network-admin 

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды