HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 204

Страница: 204 / 306

196

mode

: Configures a user-defined protocol template for the VLAN. The keywords

ethernetii

llc

, and

snap

specify the available encapsulation formats.

ethernetii etype

etype-id

: Matches the Ethernet II encapsulation format and the specified protocol

type ID. The

etype-id

argument specifies the protocol type ID of inbound packets, in the range of

0x0600 to 0xFFFF, excluding 0x0800, 0x809B, 0x8137, and 0x86DD.

llc

: Matches the LLC encapsulation format.

dsap dsap-id

: Specifies the destination service access point in the range of 0x00 to 0xFF.

ssap

ssap-id

: Specifies the source service access point in the range of 0x00 to 0xFF.

snap etype

etype-id

: Matches the SNAP encapsulation format and the specified protocol type value.

The

etype-id

argument specifies the Ethernet type of inbound packets, in the range of 0x0600 to

0xFFFF, excluding 0x8137.

protocol-index

: Specifies a protocol template index in the range of 0 to 65535. The system will

automatically assign an index if you do not specify this argument.

to protocol-end

: Specifies an end protocol template index of a protocol template range, in the range

of 0 to 65535. The value of the

protocol-end

argument must be greater than or equal to the value of

protocol-index

argument

all

: Removes all the protocols associated with the VLAN.

Usage guidelines

CAUTION:

IP uses ARP for address resolution in Ethernet. To prevent communication failures, configure the IP
and ARP templates in the same VLAN and associate them with the same port.

When you use the

mode

keyword to configure a protocol template, follow these restrictions and

guidelines:

•

Do not configure the following values for the

etype-id

argument in the

ethernetii etype

etype-id

option:

{

0x0800

—Specifies the IPv4 protocol in Ethernet II encapsulation.

{

0x809B

—Specifies the AppleTalk protocol in Ethernet II encapsulation.

{

0x8137

—Specifies the IPX protocol in Ethernet II encapsulation.

{

0x86DD

—Specifies the IPv6 protocol in Ethernet II encapsulation.

These values conflict with the

ipv4

ipx

, and

ipv6

keywords of the command, respectively.

•

Do not configure any of the following values for both the

dsap-id

and

ssap-id

arguments when

you specify the

llc

keyword:

{

0xE0

—Specifies the 802.2 LLC encapsulation format for IPX packets.

{

0xFF

—Specifies the 802.3 raw encapsulation format for IPX packets.

{

0xAA

—Specifies the 802.2 SNAP encapsulation format.

When either of the

dsap-id

and

ssap-id

arguments is configured, the system assigns 0xAA to

the other argument.

•

Do not set the

etype-id

argument in the

snap etype

etype-id

option to 0x8137. You can set the

etype-id

argument to 0x0800, 0x809B, or 0x86DD, which are corresponding to IPv4, AppleTalk,

and IPv6, respectively.

Examples

# Assign ARP packets in Ethernet II encapsulation and IPv4 packets to VLAN 3 for transmission.
(The protocol type ID for ARP is 0x0806.)

<Sysname> system-view

[Sysname] vlan 3

[Sysname-vlan3] protocol-vlan 2 mode ethernetii etype 0806

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды