manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Справочник по командам

Поделиться
Скачать
HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 13

5 

Table 2 Command output 

Field Description 

Interface 

Abbreviated interface name. 

Total (pkts/sec) 

Average rate (in pps) of receiving or sending packets during the statistics 
polling interval. 

Broadcast (pkts/sec) 

Average rate (in pps) of receiving or sending broadcast packets during the 
statistics polling interval.  

Multicast (pkts/sec) 

Average rate (in pps) of receiving or sending multicast packets during the 
statistics polling interval.  

Overflow: more than 14 
decimal digits 

The command displays 

Overflow

 if the data length of a statistical item is 

greater than 14 decimal digits. 

--: not supported 

The statistical item is not supported. 

 

Related commands 

•

 flow-interval

 

•

 

reset counters interface

 

display ethernet statistics 

Use 

display ethernet statistics

 to display the Ethernet module statistics.  

Syntax 

display ethernet statistics

 

slot slot-number 

Views 

User view 

Predefined user roles 

network-admin 

network-operator 

Parameters 

slot slot-number: 

Displays the Ethernet module statistics on the specified IRF member device. The 

slot-number

 argument represents the ID of the IRF member device. 

Examples 

# Display the Ethernet module statistics on IRF member 1. 

<Sysname>display ethernet statistics slot 1 

ETH receive packet statistics:                                                   

    Totalnum        : 28259          ETHIINum     : 22328                        

    SNAPNum         : 0              RAWNum       : 0                            

    LLCNum          : 5931           UnknownNum   : 0                            

    ForwardNum      : 22922          ARP          : 0                            

    MPLS            : 0              ISIS         : 0                            

    ISIS2           : 0              IP           : 0                            

    IPV6            : 0                                                          

ETH receive error statistics:                                                    

    NullPoint       : 0              ErrIfindex   : 0                            

    ErrIfcb         : 0              IfShut       : 0                            

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды