manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Справочник по командам

Поделиться
Скачать
HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 116

 

108 

port-isolate enable 

Use 

port-isolate enable

 to assign a port to an isolation group.

 

Use 

undo port-isolate enable

 to remove a port from an isolation group.

 

Syntax 

port-isolate enable group

 

group-number

 

undo port-isolate enable

 

Default 

The port is not assigned to any isolation group. 

Views 

Layer 2 Ethernet interface view, Layer 2 aggregate interface view 

Predefined user roles 

network-admin 

Parameters 

group

 

group-number

: Specifies an isolation group by its number in the range of 1 to 8.  

Usage guidelines 

The configuration in Layer 2 Ethernet interface view applies only to the interface. 

The configuration in Layer 2 aggregate interface view applies to the Layer 2 aggregate interface and 
its aggregation member ports. If the device fails to apply the configuration to the aggregate interface, 
it does not assign any aggregation member port to the isolation group. If the failure occurs on an 
aggregation member port, the device skips the port and continues to assign other aggregation 
member ports to the isolation group. 

You cannot assign the member ports of a service loopback group to an isolation group, and vice 
versa. 

To assign ports to an isolation group, make sure the isolation group already exists. 

One port can be assigned to only one isolation group.  

Examples 

# Assign ports GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2 to isolation group 2.  

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] port-isolate enable group 2 

[Sysname-GigabitEthernet1/0/1] quit 

[Sysname] interface gigabitethernet 1/0/2 

[Sysname-GigabitEthernet1/0/2] port-isolate enable group 2 

Related commands 

display port-isolate group

 

port-isolate group 

Use 

port-isolate group

 to create an isolation group.

 

Use 

undo port-isolate group

 to delete isolation groups.

 

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды