HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 17

Страница: 17 / 306

0 aborts, 0 deferred, 0 collisions, 0 late collisions

0 lost carrier, - no carrier

Table 4 Command output

Field Description

Current state

State of the Ethernet interface:

•

Administratively DOWN

—The Ethernet interface was shut

down with the

shutdown

command. The interface is

administratively down.

•

DOWN

—The Ethernet interface is administratively up but

physically down (possibly because no physical link is
present or the link has failed).

•

—The Ethernet interface is both administratively and

physically up.

Line protocol state

Link layer state of the interface. The state is determined through
parameter negotiation on the link layer.

•

—The interface is up at the data link layer.

•

UP (spoofing)

—The link layer protocol of an interface is UP,

but its link is an on-demand link or not present at all. This
attribute is typical of Null interfaces and loopback interfaces.

•

DOWN

—The interface is down at the data link layer.

•

DOWN (DLDP DOWN)

—The link layer protocol of the

interface is down because DLDP detected that the link was
unidirectional.

•

DOWN (LAGG DOWN)

—The link layer protocol of the

interface is down because the aggregate interface does not
have Selected ports.

•

DOWN (OAM DOWN)

—The link layer of the interface is

down because OAM detected remote link failures.

•

DOWN (DLDP and LAGG DOWN)

—The link layer of the

interface is shut down by DLDP and LAGG.

•

DOWN (DLDP and OAM DOWN)

—The link layer of the

interface is shut down by DLDP and OAM.

•

DOWN (OAM and LAGG DOWN)

—The link layer of the

interface is shut down by OAM and LAGG.

•

DOWN (DLDP, OAM and LAGG DOWN)

—The link layer of

the interface is shut down by DLDP, OAM, and LAGG.

IP packet frame type

Ethernet framing format.

PKTFMT_ETHNT_2

indicates that the

frames are encapsulated in Ethernet II framing format.

hardware address

MAC address of the interface.

Bandwidth

Expected bandwidth of the interface.

Loopback is set internal

An internal loopback test is running on the Ethernet interface.

Loopback is set external

An external loopback test is running on the Ethernet interface.

Loopback is not set

No loopback test is running on the Ethernet interface.

10Mbps-speed mode

The interface is operating at 10 Mbps.

100Mbps-speed mode

The interface is operating at 100 Mbps.

1000Mbps-speed mode

The interface is operating at 1000 Mbps.

10Gbps-speed mode

The interface is operating at 10 Gbps.

Unknown-speed mode

The speed of the interface is unknown because the speed
negotiation fails or the interface is physically disconnected.

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды