HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 212

Страница: 212 / 306

204

Private VLAN commands

display private-vlan

Use

display private-vlan

to display information about primary VLANs and their associated

secondary VLANs.

Syntax

display private-vlan

[

primary-vlan-id

]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

primary-vlan-id

: Specifies a primary VLAN ID in the range of 1 to 4094. If you do not specify a primary

VLAN ID, this command displays all primary VLANs and their associated secondary VLANs.

Examples

# Display information about primary VLANs and their associated secondary VLANs.

<Sysname> display private-vlan

Primary VLAN ID: 2

Secondary VLAN ID: 3-4

VLAN ID: 2

VLAN type: Static

Private VLAN type: Primary

Route interface: Configured

IPv4 address: 1.1.1.1

IPv4 subnet mask: 255.255.255.0

IPv6 global unicast addresses:

2001::1, subnet is 2001::/64 [TENTATIVE]

Description: VLAN 0002

Name: VLAN 0002

Tagged ports: None

Untagged ports:

GigabitEthernet1/0/2 GigabitEthernet1/0/3 GigabitEthernet1/0/4

VLAN ID: 3

VLAN type: Static

Private VLAN type: Secondary

Route interface: Not configured

Description: VLAN 0003

Name: VLAN 0003

Tagged ports: None

Untagged ports:

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды