HP Compaq 6005 Pro MT Скачать руководство пользователя страница 241

Страница: 241 / 259

Solving USB Flash Drive Problems

If you encounter USB flash drive problems, common causes and solutions are listed in the following
table.

Table D-15

Solving USB Flash Drive Problems

USB flash drive is not seen as a drive letter in Windows.

Cause

Solution

The drive letter after the last physical drive is not available.

Change the default drive letter for the flash drive in Windows.

USB flash drive not found (identified).

Cause

Solution

The device is attached to a USB port that has been hidden in
Computer Setup.

Run the Computer Setup utility and ensure that “Device
Available” is selected for the USB Ports under

Security

Device Security

The device was not properly seated before power-up.

Ensure the device is fully inserted into the USB port before
applying power to the system

System will not boot from USB flash drive.

Cause

Solution

Boot order is not correct.

Run the Computer Setup utility and change boot sequence
in

Storage

Boot Order

Removable Media Boot is disabled in the Computer Setup
utility.

Run the Computer Setup utility and enable booting to
removable media in

Storage

Storage Options

. Ensure USB

is enabled in

Storage

Boot Order

The image on the device is not bootable.

Follow the procedures described in the “ROM Flash:
Replicating the Setup: Creating a Bootable Device: Supported
USB Flash Media Device” section of the

Service Reference

Guide

The computer boots to DOS after making a bootable flash drive.

Cause

Solution

Flash drive is bootable.

Install the flash drive only after the operating system boots.

Solving USB Flash Drive Problems 229

Содержание Compaq 6005 Pro MT




































































































































































































































































Результаты поиска

Содержание Compaq 6005 Pro MT

Отзывы:

Похожие инструкции для Compaq 6005 Pro MT

Бренды по названию

Популярные бренды

HP Compaq 6005 Pro MT, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Compaq 6005 Pro MT

Отзывы:

Похожие инструкции для Compaq 6005 Pro MT

Бренды по названию

Популярные бренды