manualshive.com logo in svg

HP Compaq 6005 Pro MT, Руководство по обслуживанию и ремонту

"HP Compaq 6005 Pro MT" - мощный компьютер с высокими техническими характеристиками. Здесь вы можете скачать бесплатно руководство пользователя для ознакомления с подробными спецификациями продукта. Скачать инструкции можно на manualshive.com.

Поделиться
Скачать
background image

Solving Power Problems

Common causes and solutions for power problems are listed in the following table.

Table D-2

  Solving Power Problems

Power supply shuts down intermittently.

Cause

Solution

Power supply will not turn on because of internal power supply
fault.

Contact an authorized service provider to replace the power
supply.

Computer powered off automatically and the Power LED flashes Red two times, once every second, followed by a two
second pause, and the computer beeps two times. (Beeps stop after fifth iteration but LEDs continue flashing.)

Cause

Solution

Processor thermal protection activated:

A fan may be blocked or not turning.

OR

The heat sink is not properly attached to the processor.

1.

Ensure that the computer air vents are not blocked and
the processor cooling fan is running.

2.

Open hood, press power button, and see if the processor
fan spins. If the processor fan is not spinning, make sure
the fan's cable is plugged onto the system board header.

3.

If fan is plugged in, but is not spinning, then replace the
heat sink/fan assembly.

4.

Contact an authorized reseller or service provider.

Power LED flashes Red four times, once every second, followed by a two second pause, and the computer beeps four
times. (Beeps stop after fifth iteration but LEDs continue flashing.)

Cause

Solution

Power failure (power supply is overloaded).

1.

Open the hood and ensure the 4- or 6-wire power supply
cable is seated into the connector on the system board.

2.

Check if a device is causing the problem by removing ALL
attached devices (such as hard or optical drives and
expansion cards). Power on the system. If the system
enters the POST, then power off and replace one device
at a time and repeat this procedure until failure occurs.
Replace the device that is causing the failure. Continue
adding devices one at a time to ensure all devices are
functioning properly.

3.

Replace the power supply.

4.

Replace the system board.

204 Appendix D   Troubleshooting Without Diagnostics

Содержание Compaq 6005 Pro MT




































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Compaq 6005 Pro MT

Vecow RCS-9000 User Manual preview
RCS-9000
Бренд: Vecow Страницы: 172
DT Research DT166LX Basic Operation Manual preview
DT166LX
Бренд: DT Research Страницы: 2
Acer AcerPower M5 User Manual preview
AcerPower M5
Бренд: Acer Страницы: 48
Acer AcerPower Sc User Manual preview
AcerPower Sc
Бренд: Acer Страницы: 68
Acer 5535-5050 - Aspire Quick Manual preview
5535-5050 - Aspire
Бренд: Acer Страницы: 11
Acer AcerPower M4 User Manual preview
AcerPower M4
Бренд: Acer Страницы: 24
Acer AcerPower F1 User Manual preview
AcerPower F1
Бренд: Acer Страницы: 24
Acer AcerPower M2 User Manual preview
AcerPower M2
Бренд: Acer Страницы: 22
Acer AcerPower 8600 User Manual preview
AcerPower 8600
Бренд: Acer Страницы: 117
Acer 2010 User Manual preview
2010
Бренд: Acer Страницы: 108
Acer AcerPower S series (Portuguese) Manual Do Utilizador preview
AcerPower S series
Бренд: Acer Страницы: 53
Acer 3200 Series Service Manual preview
3200 Series
Бренд: Acer Страницы: 113
Acer 5600 series User Manual preview
5600 series
Бренд: Acer Страницы: 122
Acer AcerPower S290 Service Manual preview
AcerPower S290
Бренд: Acer Страницы: 72
Acer AcerPower APM6 Service Manual preview
AcerPower APM6
Бренд: Acer Страницы: 164
Acer AcerPower M461 Service Manual preview
AcerPower M461
Бренд: Acer Страницы: 109
Acer 3600 Series User Manual preview
3600 Series
Бренд: Acer Страницы: 122
Acer AcerPower M461 User Manual preview
AcerPower M461
Бренд: Acer Страницы: 67

Бренды по названию

Популярные бренды

Загрузить еще бренды