HP Compaq 6005 Pro MT Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 259

background image

Installing and Removing Drives

When installing additional drives, follow these guidelines:

●

The primary Serial ATA (SATA) hard drive must be connected to the dark blue primary SATA
connector on the system board labeled SATA0.

●

Connect a SATA optical drive to the white SATA connector on the system board labeled SATA1.

●

Connect devices in order of SATA0, SATA1, SATA2, then SATA3.

●

Connect an eSATA adapter cable to the orange SATA3 connector.

NOTE:

The eSATA adapter installs into one of the expansion slots on the rear of the computer.

You must configure the SATA3 connector to function as eSATA in the Computer Setup utility.
Select

Storage

>

Storage Options

>

eSATA Port

to reconfigure the SATA3 connector. Refer to

the

Computer Setup (F10) Utility Guide

for more information.

●

Connect a media card reader USB cable to the USB connector on the system board labeled MEDIA.
If the media card reader has a 1394 port, connect the 1394 cable to the 1394 PCI card.

●

The system does not support Parallel ATA (PATA) optical drives or PATA hard drives.

●

You must install guide screws to ensure the drive will line up correctly in the drive cage and lock
in place. HP has provided extra guide screws for the external drive bays (four 6-32 isolation
mounting guide screws and eight M3 metric guide screws), installed on the side of the drive bays.
The 6-32 isolation mounting screws are required for a secondary hard drive. All other drives (except
the primary hard drive) use M3 metric screws. The HP-supplied metric screws are black and the
HP-supplied isolation mounting screws are silver and blue. If you are replacing the primary hard
drive, you must remove the four silver and blue 6-32 isolation mounting guide screws from the old
hard drive and install them in the new hard drive.

Figure 8-15

Extra Guide Screw Locations

No.

Guide Screw

Device

1

Black M3 Metric Screws

All Other Drives (except primary hard drive)

2

Silver and Blue 6-32 Isolation Mounting Screws

Secondary Hard Drive

88

Chapter 8 Removal and Replacement Procedures Microtower (MT) Chassis

«
...
98
99
100
101
102
...
»

Содержание Compaq 6005 Pro MT




































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Compaq 6005 Pro MT

Бренд: Acer Страницы: 17

Бренд: Acer Страницы: 19

Presario SR5700 - Desktop PC

Бренд: Compaq Страницы: 76

Бренд: Acer Страницы: 55

Бренд: Acer Страницы: 89

Бренд: Acer Страницы: 86

Aspire G7750 Series

Бренд: Acer Страницы: 108

Aspire L series

Бренд: Acer Страницы: 51

Aspire E series

Бренд: Acer Страницы: 38

Бренд: Acer Страницы: 90

Aspire AZS600_P

Бренд: Acer Страницы: 240

Бренд: Acer Страницы: 90

Бренд: Acer Страницы: 68

Aspire E 14 Series

Бренд: Acer Страницы: 63

Бренд: Acer Страницы: 87

Бренд: Acer Страницы: 104

Aspire iDea 500 Series

Бренд: Acer Страницы: 87

Бренд: Acer Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды