HP Compaq 6005 Pro MT Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 259

background image

Installing and Removing Drives

When installing additional drives, follow these guidelines:

●

The primary Serial ATA (SATA) hard drive must be connected to the dark blue primary SATA
connector on the system board labeled SATA0.

●

Connect a SATA optical drive to the white SATA connector on the system board labeled SATA1.

●

Connect devices in order of SATA0, SATA1, SATA2, then SATA3

●

Connect an eSATA adapter cable to the orange SATA3 connector.

NOTE:

The eSATA adapter installs into one of the expansion slots on the rear of the computer.

You must configure the SATA3 connector to function as eSATA in the Computer Setup utility.
Select

Storage

>

Storage Options

>

eSATA Port

to reconfigure the SATA3 connector. Refer to

the

Computer Setup (F10) Utility Guide

for more information.

●

Connect a media card reader USB cable to the USB connector on the system board labeled MEDIA.
If the media card reader has a 1394 port, connect the 1394 cable to the 1394 PCI card.

●

The system does not support Parallel ATA (PATA) optical drives or PATA hard drives.

●

You must install guide screws to ensure the drive will line up correctly in the drive cage and lock
in place. HP has provided extra guide screws for the external drive bays (five 6-32 standard screws
and four M3 metric screws), installed in the front of the chassis, under the front bezel. The 6-32
standard screws are required for a secondary hard drive. All other drives (except the primary hard
drive) use M3 metric screws. The HP-supplied metric screws are black and the HP-supplied
standard screws are silver. If you are replacing the primary hard drive, you must remove the four
silver and blue 6-32 isolation mounting guide screws from the old hard drive and install them in the
new hard drive.

Figure 9-16

Extra Guide Screw Locations

No.

Guide Screw

Device

1

Black M3 Metric Screws

All Other Drives (except primary hard drive)

2

Silver 6-32 Standard Screws

Secondary Hard Drive

There are at total of five extra silver 6-32 standard screws. Four are used as guide screws for a secondary
hard drive. The fifth is used for bezel security.

136 Chapter 9 Removal and Replacement Procedures Small Form Factor (SFF) Chassis

«
...
146
147
148
149
150
...
»

Содержание Compaq 6005 Pro MT




































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Compaq 6005 Pro MT

Бренд: NComputing Страницы: 16

Бренд: Olivetti Страницы: 111

Бренд: IBM Страницы: 52

Бренд: Wasp Barcode Technologies Страницы: 69

ARK-5280 Series

Бренд: Advantech Страницы: 88

Бренд: Aaeon Страницы: 117

Бренд: Magic Страницы: 19

Бренд: Spectravideo Страницы: 134

GX520 - OptiPlex - 512 MB RAM

Бренд: Dell Страницы: 266

Бренд: Dell Страницы: 74

Бренд: NEC Страницы: 110

Бренд: NEC Страницы: 2

PowerMate VT 300i Series

Бренд: NEC Страницы: 190

PowerMate Ready ES Pro

Бренд: NEC Страницы: 109

Ready 9734ES Pro

Бренд: NEC Страницы: 76

POWERMATE VT 300 RELEASE NOTES

Бренд: NEC Страницы: 192

Бренд: NEC Страницы: 253

PowerMate V100e

Бренд: NEC Страницы: 155

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды