HP Compaq 6005 Pro MT Скачать руководство пользователя страница 117

Страница: 117 / 259

Front I/O Assembly

Prepare the computer for disassembly (

Preparation for Disassembly on page 74

Remove the computer access panel (

Access Panel on page 75

Remove the front bezel (

Front Bezel on page 76

Remove the cables from the clip on top of the baffle.

Disconnect the three front I/O cables (yellow, green, and blue) from the system board connectors
(FRNT_USB1, FRNT_USB2, and FRNT_AUD).

Remove the silver T15 screw

(1)

that secures the assembly to the chassis.

Rotate the assembly to the right

(2)

, and then lift the assembly away from the computer while

threading the wires through the hole in the front of the chassis.

To reinstall the panel, reverse the removal procedure.

Front I/O Assembly 105

Содержание Compaq 6005 Pro MT




































































































































































































































































Результаты поиска

Содержание Compaq 6005 Pro MT

Отзывы:

Похожие инструкции для Compaq 6005 Pro MT

Бренды по названию

Популярные бренды

HP Compaq 6005 Pro MT, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Compaq 6005 Pro MT

Отзывы:

Похожие инструкции для Compaq 6005 Pro MT

Бренды по названию

Популярные бренды