manualshive.com logo in svg

Hoval UltraGas 1000, Техническая информация, Страница: 4 / 58

Поделиться
Скачать
Hoval UltraGas 1000 Скачать руководство пользователя страница 4

1.

Important notes

1.1 

General safety instructions

The system may only be placed in operation 

if all the relevant standards and safety regula-

tions have been complied with.

At least the following conditions must be satisfied for a tri

-

al operation:

• Safety valve installed (system sealed)

• Control system in operation (connected to the power

supply)

• Sensor for safety temperature limiter connected (= boil-

er temperature sensor)

•

System filled with water

•

Condensation trap filled with water

• Expansion tank connected

•

Flue gas outlet with flue gas conduit connected to flue

gas system.

• Burner preset (see point 6.7).

WARNING

The heat generator can only be de-energised 

by disconnection from the mains (e.g. all-

pole switch).

WARNING

All electric power supply circuits must be 

switched off before accessing the terminals.

1.2 

Explanation of the symbols

1.2.1  Warnings

!

DANGER

... indicates a situation of immediate danger 

which will lead to serious or fatal injuries if 

not avoided.

!

WARNING

... indicates a situation of possible danger 

which can lead to serious or fatal injuries if 

not avoided.

!

CAUTION

... indicates a situation of possible danger 

which can lead to minor or slight injuries if 

not avoided.

NOTICE

... indicates a situation of possible danger 

which can lead to damage to property if not 

avoided.

1.2.2  Warning symbols

The following warning signs are combined for the warn-

ing notes with signal words CAUTION, WARNING and 

DANGER.

!

General warning of a danger zone.

«Warning: dangerous electrical voltage» as a 

warning for accident prevention.

Ensures that people do not come into contact 

with electrical voltage. The danger sign with 

the black lighting symbol warns against the 

danger of electrical voltage.

«Warning of hot surface» sign for indicating 

safety.

Indicates dangers of injury and burns on hot 

surfaces.

Incorrect handling of potentially explosive 

substances can lead to serious damage, po-

tentially fatal injuries and incalculable costs.

Danger: Substances with a corrosive effect on 

skin, eyes and respiratory organs; can cause 

irritation.

Handling: Do not inhale vapours and avoid 

contact with skin and eyes.

4

4 217 215 / 00

IMPORTANT NOTES

Содержание UltraGas 1000



























































Отзывы:

Нет отзывов