Hoshizaki KM-470AJ Скачать руководство пользователя страница 24

Страница: 24 / 44

3. Low Ice Production

Low Ice Production - Possible Cause

Long Harvest Cycle

1. Evaporator

a) Scaled up.

2. Spray Tubes and/or Spray

Guides

a) Dirty.
b) Out of position.

3. Refrigerant Charge

a) Low.

4. Water Supply

a) Low water pressure.
b)

External water filters clogged.

Insufficient water line size.

Minimum 1/4" Nominal ID (6 mm Nominal OD in the EU) water

tubing or equivalent.

d) Too cold.

5. Control Board

See "II.C. Control Board Check"

a) Thermistor connection loose (K3).
b) Defective.

6. Thermistor

See "II.F. Thermistor Check"

a) Loose, disconnected, or defective.

7. Hot Gas Valve

a) Erratic or closed.

8. Inlet Water Valve

Screen or orifice clogged.

9. Compressor

Inefficient or off.

10. Liquid Line Valve

a) Erratic or open.

11. Thermostatic Expansion Valve

a) Defective.

Long Freeze Cycle

1. Evaporator

a) Scaled up, dirty.

2. Float Switch

See "II.E. Float Switch Check

and Cleaning"

a) Scaled up, dirty.
b) Float sticking.
c) Defective switch.

3. Inlet Water Valve

a) Leaking by.

4. Hot Gas Valve

a) Erratic or open.

5. Condenser

a) Clogged.

6. Control Board

See "II.C. Control Board Check"

a) Float switch connection loose (K5).
b) Defective.

7. Refrigerant Charge

a) Low.

8. Thermostatic Expansion Valve

a) Bulb loose.
b) Defective.

9. Compressor

Inefficient or off.

10. Pump Motor

a) RPM too slow.

11. Liquid Line Valve

a) Erratic or restricted.

Содержание KM-470AJ













































Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды

Hoshizaki KM-470AJ, Руководство по обслуживанию

Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды