Hoshizaki KM-470AJ Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 44

background image

26

III. Controls and Adjustments

• A Hoshizaki exclusive control board is employed in KM series appliances.
• All models are pretested and factory adjusted.
• For a control board check procedure, see "II.C. Control Board Check."

NOTICE

• Fragile, handle very carefully.
• The control board contains integrated circuits, which are susceptible to failure

due to static discharge. It is especially important to touch the metal part of the

icemaker when handling or replacing the control board.

• Do not touch the electronic devices on the control board or the back of the control

board.

• Do not change wiring and connections. Do not misconnect K3 WHITE, K4 RED,

and K5 BLACK, because the same connector is used for the thermistor, jumper,

and float switch.

• Do not short out power supply to test for voltage.
• Always replace the whole control board assembly if it goes bad.

«
...
24
25
26
27
28
...
»

Содержание KM-470AJ













































Отзывы:

Нет отзывов

Похожие инструкции для KM-470AJ

PROFESSIONAL BELGIAN IB08WR119

Бренд: Waring Страницы: 16

Maxx Ice UIM225NB

Бренд: UniFlow Страницы: 56

AROMATICA U27.51

Бренд: Rotel Страницы: 73

Бренд: BRAYER Страницы: 52

Бренд: Hoshizaki Страницы: 29

Бренд: Kalorik Страницы: 26

Бренд: Felix Storch Страницы: 88

SPECIAL SELECT FSCM200BM

Бренд: Farberware Страницы: 12

Бренд: Bunn Страницы: 36

Бренд: Follett Страницы: 12

Бренд: Saeco Страницы: 33

Бренд: Saeco Страницы: 48

Бренд: Haier Страницы: 28

Бренд: Haier Страницы: 80

Бренд: Lakeland Страницы: 20

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды