Hoshizaki KM-470AJ Скачать руководство пользователя страница 41

Страница: 41 / 44

2. Remove the water from the water tank:

1) Turn off the power supply, then remove the front panel.

2) Move the control switch to the "OFF" position.

3) Drain the water tank. Remove the rubber cap covering the overflow pipe in the water

tank. Remove the overflow pipe by turning it counterclockwise. After the water tank

has drained, replace the overflow pipe and the rubber cap in their correct positions.

NOTICE

Make sure the O-ring is attached to the bottom of the overflow pipe and

be careful not to cross thread the overflow pipe.

4) Replace the base cover (if applicable) and front panel in their correct positions.
5) Remove all ice from the dispensing unit/ice storage bin. Clean the storage bin liner

using a neutral cleaner. Rinse thoroughly after cleaning.

Fig. 3

Rubber Cap

Overflow Pipe

Sleeve

O-Ring

Cube Guide

Содержание KM-470AJ













































Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды

Hoshizaki KM-470AJ, Руководство по обслуживанию

Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды