Hoshizaki KM-470AJ Скачать руководство пользователя страница 2

Страница: 2 / 44

CONTENTS

Important Safety Information ................................................................................................. 3

I. Construction and Water/Refrigeration Circuit Diagram ...................................................... 5

A. Construction .................................................................................................................. 5

B. Water/Refrigeration Circuit Diagram ............................................................................. 6

II. Sequence of Operation and Service Diagnosis ................................................................. 7

A. Sequence of Operation Flow Chart .............................................................................. 7

B. Service Diagnosis ......................................................................................................... 9

C. Control Board Check .................................................................................................. 16

D. Bin Control Check ....................................................................................................... 17

E. Float Switch Check and Cleaning ............................................................................... 18

F. Thermistor Check ........................................................................................................ 20

G. Control Switch ............................................................................................................ 20

H. Diagnostic Tables........................................................................................................ 21

I. Freeze-Up Check List .................................................................................................. 25

III. Controls and Adjustments............................................................................................... 26

A. Control Board Layout .................................................................................................. 27

B. LED Lights and Audible Alarm Safeties ...................................................................... 28

C. Settings and Adjustments ........................................................................................... 29

1. Default Dip Switch Settings ................................................................................... 29

2. Harvest Timer (S4 dip switch 1 & 2) ...................................................................... 30

3. Pump-Out Timer/Harvest Time During Pump-Out (S4 dip switch 3 & 4) ............... 30

4. Pump-Out Frequency Control (S4 dip switch 5) .................................................... 31

5. Harvest Pump Time (Harvest Assist Duration) (S4 dip switch 6) .......................... 31

6. Harvest Pump Time (Harvest Assist) (S4 dip switch 7) ........................................ 32

7. Factory Use (S4 dip switch 8) ............................................................................... 32

8. Freeze Timer (S4 dip switch 9 & 10) ..................................................................... 33

9. Float Switch Selector (S5 dip switch 1) ................................................................. 33

10. Refill Counter (S5 dip switch 2 and 3)

................................................................. 33

11. Minimum Harvest Time (S5 dip switch 4) ............................................................ 34

12. Anti-Slush (S5 dip switch 5)................................................................................. 34

IV. Refrigeration Circuit and Component Service Information ............................................. 35

A. Refrigeration Circuit Service Information .................................................................... 35

B. Component Service Information ................................................................................. 38

V. Maintenance .................................................................................................................... 39

VI. Preparing the Appliance for Periods of Non-Use ........................................................... 40

VII. Disposal ........................................................................................................................ 42

VIII. Technical Information ................................................................................................... 43

A. DIMENSIONS/SPECIFICATIONS .............................................................................. 43

B. Wiring Diagram .......................................................................................................... 44

IMPORTANT

This manual should be read carefully before the appliance is serviced. Read

the warnings and guidelines contained in this manual carefully as they provide

essential information for the continued safe use, service, and maintenance of the

appliance. Retain this manual for any further reference that may be necessary.

Содержание KM-470AJ













































Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды

Hoshizaki KM-470AJ, Руководство по обслуживанию

Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды